3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
CompTIA®A+ Exam Notes : Compare And Contrast The Characteristics Of Connectors And Cabling 1. A+ Core 1 Exam Download 2. A+ Core 2 Exam Download 3. A+ Lab Simulator Download
2. Networking 2.2 Compare and contrast the characteristics of connectors and cabling.
Thin co-axial and thick co-axial cables have conductive grounding sheath surrounding the center conductor. Therefore, the electromagnetic interference (EMI) is significantly less. Fiber optic cabling is immune to crosstalk and other electrical interference because optical fiber does not conduct electricity and uses light signals in a glass fiber, rather than electrical signals along a metallic conductor to transmit data. So it cannot produce a magnetic field and thus is immune to EMI. In twisted pair cable, the noise introduced into the twisted pair wire is canceled as the electrical signals pass through the wire. However, it is not possible to reduce the electrical interference totally in a TP wire .Instead of transferring data over copper wires, these cables contain optical fibers that transmit data via light, rather than pulses of electricity. Each optical fiber is individually coated with plastic layers and contained in a protective tube, making it extremely resistant to external interference. Twisted Pair cable Types: STP stands for Shielded Twisted Pair and UTP stands for Unshielded Twisted Pair. Shielded Twisted Pair (STP)cables reduce electrical noise and electromagnetic radiation. In other words, they help to keep the signal steady, and reduce interference with other devices. Given below is a diagram showing a typical shielded twisted pair cable
https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
1/6
3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
Unshielded Twisted Pair (UTP)cables do not have shielding to reduce interference. They are designed to cancel electromagnetic interference with the way the pairs are twisted inside the cable. Unshielded twisted cables are most widely used for office LANs, though recently wireless LANs are more widely used. Unshielded cables are lightweight, thin and flexible. They are also versatile and inexpensive. A typical UTP cable cross section is shown in the figure below:
Comparison between STP and UTP 1. Physical: The only difference between the STP and UTP cable is the additional shielding material used in STP cables. The shielding covers the full length of the cable and protects it from any external interference. 2. Cost: Due to the additional material used in a STP cable, it costs more than the UTP cable. 3. Considerations: While using STP cable will yield maximum bandwidth despite external conditions, the shielding makes the cable heavier and more difficult to bend. 4. Use: UTP cable typically is used in homes and offices. Some large businesses also use the cable because it is cheaper. Large companies that require maximum bandwidth typically use STP cable. STP cable is used outside to better deal with the elements and equipment that may degrade bandwidth quality. The various wiring schemes for UTP https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
2/6
3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
CAT3 Speed
16 Mbps
CAT5 CAT5e CAT6 CAT6e CAT7 100 1000 10/100/1000Mbps 10/100/1000Mbps 10/100/1000Mbps Mbps Mbps and 10 Gbps and 10 Gbps and 10 Gbps
Ineffective for Higher – speed Range Range networks Range of 100 Limitation of 100 of 100 often found meters meters meters in older 10BaseT networks
Range of 100 meters
Range of 100 meters
For connecting to an Ethernet LAN, you need an RJ-45 connector at the network end of the cable. The maximum allowed length of the cable for 1000BaseT Gigabit Ethernet is 100 meters (without repeater) Category 3: Used in 10BASE-T networks. Can transmit data at speeds up to 10 Mbps. Category 5: Can transmit data at speeds up to 100 Mbps. Widely used in 100BaseT Ethernet networks. Category 5e: Used in networks running at speeds up to 1000 Mbps (1 gigabit per second [Gbps]). The Cat-5e cable may be used in 1000BaseT Ethernet network. Both Cat -5 and 5e are almost same, except for better noise (cross talk, etc.) specs associated with 5e. Cat 5e or better cable type is used for Gigabit Ethernet network cabling. Cat5e cable contains four twisted pairs of wires for Gigabit Ethernet. Category 6: Category 6 cable, commonly referred to as Cat-6, is a cable standard for Gigabit Ethernet and other network protocols that is backward compatible with the Category 5/5e and Category 3 cable standards. The cable contains four twisted copper wire pairs. This is same as CAT5 and CAT5e copper cable standards. The cable standard is suitable for 10BASE -T / 100BASE-TX and 1000BASE -T / 1000BASE-TX (Gigabit Ethernet). Category 7: The Category 7 cable standard has been created to allow 10 Gigabit Ethernet over 100 m of copper cabling. CAT 7 is backwards compatible with traditional Cat5 and Cat6 Ethernet. Cat7 offers strict specifications for crosstalk and system noise than Cat6. Shielding has been added for individual wire pairs on the Category 7 cable. Cat7 has been designed as a standard for Gigabit Ethernet over 100m of copper cabling. The cable contains four twisted copper wire pairs, just like the earlier standards.
CAT5e is sufficient and can also handle gig Ethernet, but noise margin will be less. https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
3/6
3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
CAT6 is rated for gigabit Ethernet while CAT6e is thicker and rated for 10 gig Ethernet. Typically Note: RJ-11 connector has only two pairs of wires, and normally used for connecting telephones. IEEE 1394 cabling consists of shielded cable pairs. There are 4 and 6 wire versions of this cable type, known as STP, used in IEEE1394 connections. IEEE 1394, High Performance Serial Bus, is an electronics standard for connecting devices to personal computer. IEEE 1394 provides a single plugand-socket connection on which up to 63 devices can be attached with data transfer speeds up to 400Mbps(megabits per second). FireWire is Apple's name for the IEEE 1394 High Speed Serial Bus. A standard FireWire connection will support 100,200 and 400 Mbps. The important features of IEEE1394 (also known as FireWire 400) are: 1. 100 Mbit/s, 200Mbit/s, and 400Mbit/s supported. 2. Works without control, devices communicate peer-to-peer. 3. Cable up to 4.5 m. 4. Up to 63 devices supported. 5. Power supply to external devices is 1.25A/12V (max.). 6. The only computer bus used in digital video cameras. Power over Ethernet or PoE: PoE technology describes a system to pass electrical power safely, along with data, on Ethernet cabling. The IEEE standard for PoE requires category 5 cable or higher for high power levels, but can operate with category 3 cable if less power is required. System Preparation(Sysprep): System Preparation tool prepares an installation of Windows for duplication, auditing, and customer delivery. Duplication, also called imaging, enables you to capture a customized Windows image that you can reuse throughout an organization. Audit mode enables you to add additional device drivers or applications to a Windows installation. After you install the additional drivers and applications, you can test the integrity of the Windows installation. Sysprep also enables you to prepare an image to be delivered to a customer. When the customer boots Windows, Windows Welcome starts. https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
4/6
3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
RG-6 and RG-59: RG-6 may be used for both analog and digital television transmission. RG-59 is a specific type of coaxial cable, often used for low-power video and RF signal connections Comparison between RG-6 and RG-59 1. RG6 cable has a thicker conductor than the RG59 2. RG6 cable has better insulation than the RG59 3. RG6 can carry signals of much higher frequencies than the RG59 4. RG6 has much lower signal losses compared to the RG59 5. RG6 cable may not operate below 50Mhz while the RG59 can 6. RG6 is better for satellite signals while RG59 is better for video signals 7. RG6 cables cost more than RG59 Previous Contents Next A+ Core 1 Cram Notes Contents
1. Hardware 1.1 BIOS Tools on a PC 1.2 Motherboard Components and their purpose 1.3 Identify common PC connector types and associated cables 1.4 Various PC connection interfaces, their characteristics and purpose. 1.5 Various memory (RAM) types and their features 1.6 Install and configure PC expansion cards. 1.7 Install and configure storage devices and use appropriate media. 1.8 Install various types of CPUs and apply the appropriate cooling methods. 1.9 Install a power supply based on given specifications. 1.10 Compare and contrast types of display devices and their features. 1.11 Install and configure common peripheral devices 1.12 Compare and contrast differences between the various print technologies and the associated imaging 1.13 Given a scenario, select the appropriate components for a custom PC
2. Networking 2.1 Identify the various types of network cables and connectors. 2.2 Compare and contrast the characteristics of connectors and cabling. 2.3 Explain the properties and characteristics of TCP/IP.
3. Mobile Devices 3.1 Laptop hardware and components. 3.2 Function of components within the display of a laptop. 3.3 Characteristics of various types of other mobile devices. 3.4 Given a scenario, configure basic mobile device network connectivity and application support. 3.5 Given a scenario, use methods to perform mobile device synchronization https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
5/6
3/4/24, 12:11 PM
comptia A+ Core 1 - Characteristics Of Connectors And Cabling.
4. Hardware and Network Troubleshooting 4.1 Troubleshoot common problems related to motherboards, RAM, CPU and power with appropriate tools 4.2 Troubleshoot wired and wireless networks with appropriate tools. 4.3 Troubleshoot hard drives and RAID arrays with appropriate tools. 4.4 Troubleshoot common video and display issues 4.5 Troubleshoot printers with appropriate tools
5. Virtualization and Cloud Computing 5.1 Compare and contrast cloud computing concepts 5.2 Given a scenario, set up and configure client-side virtualization
1. A+ Core 1 Exam Download 2. A+ Core 2 Exam Download 3. A+ Lab Simulator Download
https://www.examguides.com/Aplus-Core1/aplus-core1-16.htm
6/6
